skip to navigation
skip to content

Not Logged In

Pibrella 1.1.3dev

A module to control the Pibrella Raspberry Pi Addon Board

Pibrella

Support code and API library for the Pibrella addon board.

Installation

The easy way, just:

pip install pibrella

Alternatively you can clone this repository and install:

git clone http://github.com/pimoroni/pibrella cd pibrella sudo python setup.py install

To try the examples:

git clone http://github.com/pimoroni/pibrella cd pibrella/examples sudo python siren.py

Usage

Run as root!

Pibrella depends upon RPi.GPIO > 0.5.4, which requires root to access your GPIO.

If you're using an interactive shell you should: sudo python -i, otherwise sudo python yourscript.py

First steps

To get started you need to import pibrella. Simply:

import pibrella

This will set up GPIO for you and collect all of the Pibrella's inputs and outputs into some handily named objects.

If, for example, you wanted to turn on an LED you could:

pibrella.light.red.on()

And to turn it off again:

pibrella.light.red.off()

Pibrellas collections ( lights, inputs, outputs ) allow you to also control a group of things at the same time. So to turn all of the LEDs off you can simply:

pibrella.light.off()

Or on:

pibrella.light.on()

Blinking and pulsing LEDs

Lights aren't simply there for toggling on and off. Any good lighting display needs pulsing, fading, blinking and strobing. Pibrella has functions for those, too:

pibrella.light.red.blink(ON_TIME, OFF_TIME)

And something more exciting:

pibrella.light.red.pulse(FADE_IN_TIME, FADE_OUT_TIME, ON_TIME, OFF_TIME)

The astute observer will realise that these are equivilent:

pibrella.light.red.pulse(0, 0, 1, 1) pibrella.light.red.blink(1, 1)

You can also fade LEDs from one brightness to another, like so:

pibrella.light.red.fade(0, 100, 2) # From 0 to 100% in 2 seconds

Inputs and outputs

The input and output collections correspond to the 4 in and 4 out pins of the Pibrella. These are named a, b, c, d for inputs and e, f, g, h for outputs- you'll see these labels on the board itself.

To turn output "e" on, you can:

pibrella.output.e.on()

You can also write an explicit value, ( 1 is on/high, 0 is off/low ) like so

pibrella.output.e.write(1)

This is useful if you want to toggle a pin on and off programmatically, or write an input value directly to an output.

And you can write to the whole output collection simultaneously if you wish:

pibrella.output.write(1)

Inputs are similar, except you're reading them instead of turning them on and off. To read a single input:

my_value = pibrella.input.e.read()

Or to read all inputs into a dictionary:

inputs = pibrella.input.read() input_e = inputs['e']

The button

The Pibrella button is, for all intents and purposes, just another input. It does, however, have a pull-down resistor enabled to prevent it reading random electrical fluctuations as button presses.

Like an input, you can read the button state at any time:

pibrella.button.read()

The buzzer

The buzzer is just another output. However just turning it on and off wont get you much more than a single pop, it needs to be toggled rapidly to make a continuous tone. We've provided functions for this.

First, you can buzz at a specific frequency:

pibrella.buzzer.buzz( frequency )

Or play a note ( you can use both positive and negative values here, with 0 being A at 440Hz )

pibrella.buzzer.note( 1 )

Or play a built-in tone:

pibrella.buzzer.fail() pibrella.buzzer.success()

Handling events

If you want to catch an input changing state and run a specific function, you can use changed, pressed and released on any of the inputs or the button. Changed will trigger when a pin transitions from 1 ( high/on ) to 0 ( low/off ) or vice versa. Pressed will trigger when it transitions from 0 to 1, and Released when it transitions from 1 to 0.

For example:

def button_pressed(pin):
print("You pressed the button!")

pibrella.button.pressed(button_pressed)

The "pin" parameter of the button pressed function is the Pibrella pin that triggered the event, in this case "pin" will be equal to "pibrella.button" so you can .read() it.

def button_changed(pin):
if pin.read() == 1:
print("You pressed the button!")
else:
print("You released the button!")

pibrella.button.changed(button_changed)

If you want to turn a light on when the button is pressed, your code should look something like this:

import pibrella

def button_changed(pin):
pibrella.light.red.write(pin.read())

pibrella.button.changed(button_changed)

And in just 4 lines, you've got started with event-driven programming!

Change Log

1.1.3-dev

  • Built-in asyncronous alarm sound! pibrella.buzzer.alarm()
  • Replaced xrange with range

1.1.2-dev

  • Added support for REV 1 Raspberry Pi

1.1.1-dev

  • Added fade(from,to,duration) for lights

1.1-dev

  • Removed .all. keyword, use pibrella.input.read() instead of pibrella.input.all.read()
  • Added helper to list pins, try: pibrella.input in interactive shell
  • Added ['name'] and [idx] support to pin collections, try: pibrella.input[0] pibrella.input['a']
  • Added buzzer to pibrella.pin
  • Added return values to most methods

1.0-dev

  • Initial development/beta release
 
File Type Py Version Uploaded on Size
Pibrella-1.1.3dev.tar.gz (md5) Source 2014-03-02 9KB
  • Downloads (All Versions):
  • 16 downloads in the last day
  • 135 downloads in the last week
  • 598 downloads in the last month