Audio Modem Communication Library
Project description
Description
This program can be used to transmit a specified file between 2 computers, using a simple audio cable (for better SNR and higher speeds) or a simple headset, allowing true air-gapped communication (via a speaker and a microphone).
The sender modulates an input binary data file into an 32kHz audio, which is played to the sound card.
The receiver side records the transmitted audio, which is demodulated concurrently into an output binary data file.
The process requires a single manual calibration step: the transmitter has to find maximal output volume for its sound card, which will not saturate the receiving microphone.
The modem is using OFDM over an audio cable with the following parameters:
Sampling rate: 32 kHz
Baud rate: 1 kHz
Symbol modulation: BPSK, 4-PSK, 16-QAM ,64-QAM, 256-QAM
Carriers: 2-11 kHz
This way, modem may achieve 80kbps bitrate = 10 kB/s (for best SNR).
A simple CRC-32 checksum is used for data integrity verification on each 250 byte data frame.
Installation
Make sure that numpy and PortAudio v19 packages are installed (on Debian):
$ sudo apt-get install python-numpy portaudio19-dev
Get the latest released version from PyPI:
$ pip install --user amodem
Or, try the latest (unstable) development version from GitHub:
$ git clone https://github.com/romanz/amodem.git $ cd amodem $ pip install --user -e .
For graphs and visualization (optional), install matplotlib Python package.
For validation, run:
$ export BITRATE=48 # explicitly select high MODEM bit rate (assuming good SNR).
$ amodem-cli -h
usage: amodem-cli [-h] {send,recv} ...
Audio OFDM MODEM: 48.0 kb/s (64-QAM x 8 carriers) Fs=32.0 kHz
positional arguments:
{send,recv}
send modulate binary data into audio signal.
recv demodulate audio signal into binary data.
optional arguments:
-h, --help show this help message and exit
Calibration
Connect the audio cable between the sender and the receiver, and run the following scripts:
On the sender’s side:
~/sender $ export BITRATE=48 # explicitly select high MODEM bit rate (assuming good SNR). ~/sender $ amodem-cli send --calibrate
On the receiver’s side:
~/receiver $ export BITRATE=48 # explicitly select high MODEM bit rate (assuming good SNR). ~/receiver $ amodem-cli recv --calibrate
If BITRATE is not set, the MODEM will use 1 kbps settings (single frequency with BPSK modulation).
Change the sender computer’s output audio level, until all frequencies are received well:
3000 Hz: good signal 4000 Hz: good signal 5000 Hz: good signal 6000 Hz: good signal 7000 Hz: good signal 8000 Hz: good signal 9000 Hz: good signal 10000 Hz: good signal
If the signal is “too weak”, increase the sender’s output audio level.
If the signal is “too strong”, decrease the sender’s output audio level.
If the signal is “too noisy”, it may be that the noise level is too high or that the analog signal is being distorted. Please run the following command during the calibration session, and send me the resulting audio.raw file for debugging:
~/receiver $ arecord --format=S16_LE --channels=1 --rate=32000 audio.raw
You can see a video of the calibration process.
Usage
Prepare the sender (generate a random binary data file to be sent):
~/sender $ dd if=/dev/urandom of=data.tx bs=60KB count=1 status=none ~/sender $ sha256sum data.tx 008df57d4f3ed6e7a25d25afd57d04fc73140e8df604685bd34fcab58f5ddc01 data.tx
Start the receiver (will wait for the sender to start):
~/receiver $ amodem-cli recv -vv -i data.rx
Start the sender (will modulate the data and start the transmission):
~/sender $ amodem-cli send -vv -o data.tx
A similar log should be emitted by the sender:
2015-02-06 18:12:46,222 DEBUG Audio OFDM MODEM: 48.0 kb/s (64-QAM x 8 carriers) Fs=32.0 kHz amodem-cli:191 2015-02-06 18:12:46,222 INFO PortAudio V19-devel (built Feb 25 2014 21:09:53) loaded audio.py:19 2015-02-06 18:12:48,297 INFO Sending 2.150 seconds of training audio main.py:21 2015-02-06 18:12:48,297 INFO Starting modulation main.py:26 2015-02-06 18:12:49,303 DEBUG Sent 6.000 kB send.py:48 2015-02-06 18:12:50,296 DEBUG Sent 12.000 kB send.py:48 2015-02-06 18:12:51,312 DEBUG Sent 18.000 kB send.py:48 2015-02-06 18:12:52,290 DEBUG Sent 24.000 kB send.py:48 2015-02-06 18:12:53,299 DEBUG Sent 30.000 kB send.py:48 2015-02-06 18:12:54,299 DEBUG Sent 36.000 kB send.py:48 2015-02-06 18:12:55,306 DEBUG Sent 42.000 kB send.py:48 2015-02-06 18:12:56,296 DEBUG Sent 48.000 kB send.py:48 2015-02-06 18:12:57,311 DEBUG Sent 54.000 kB send.py:48 2015-02-06 18:12:58,293 DEBUG Sent 60.000 kB send.py:48 2015-02-06 18:12:58,514 INFO Sent 60.000 kB @ 10.201 seconds main.py:31 2015-02-06 18:12:59,506 DEBUG Closing input and output
A similar log should be emitted by the receiver:
2015-02-06 18:12:44,848 DEBUG Audio OFDM MODEM: 48.0 kb/s (64-QAM x 8 carriers) Fs=32.0 kHz amodem-cli:191 2015-02-06 18:12:44,849 INFO PortAudio V19-devel (built Feb 25 2014 21:09:53) loaded audio.py:19 2015-02-06 18:12:44,929 DEBUG AsyncReader thread started async.py:23 2015-02-06 18:12:44,930 DEBUG Skipping 0.100 seconds main.py:44 2015-02-06 18:12:45,141 INFO Waiting for carrier tone: 3.0 kHz main.py:51 2015-02-06 18:12:47,846 INFO Carrier detected at ~2265.0 ms @ 3.0 kHz detect.py:59 2015-02-06 18:12:47,846 DEBUG Buffered 1000 ms of audio detect.py:61 2015-02-06 18:12:48,025 DEBUG Carrier starts at 2264.000 ms detect.py:71 2015-02-06 18:12:48,029 DEBUG Carrier symbols amplitude : 0.573 detect.py:96 2015-02-06 18:12:48,030 DEBUG Current phase on carrier: 0.061 detect.py:107 2015-02-06 18:12:48,030 DEBUG Frequency error: -0.009 ppm detect.py:108 2015-02-06 18:12:48,030 DEBUG Frequency correction: 0.009 ppm main.py:55 2015-02-06 18:12:48,030 DEBUG Gain correction: 1.746 main.py:58 2015-02-06 18:12:48,198 DEBUG Prefix OK recv.py:46 2015-02-06 18:12:48,866 DEBUG 3.0 kHz: SNR = 34.82 dB recv.py:90 2015-02-06 18:12:48,866 DEBUG 4.0 kHz: SNR = 36.39 dB recv.py:90 2015-02-06 18:12:48,867 DEBUG 5.0 kHz: SNR = 37.88 dB recv.py:90 2015-02-06 18:12:48,867 DEBUG 6.0 kHz: SNR = 38.58 dB recv.py:90 2015-02-06 18:12:48,867 DEBUG 7.0 kHz: SNR = 38.86 dB recv.py:90 2015-02-06 18:12:48,867 DEBUG 8.0 kHz: SNR = 38.63 dB recv.py:90 2015-02-06 18:12:48,867 DEBUG 9.0 kHz: SNR = 38.07 dB recv.py:90 2015-02-06 18:12:48,868 DEBUG 10.0 kHz: SNR = 37.22 dB recv.py:90 2015-02-06 18:12:48,869 INFO Starting demodulation recv.py:124 2015-02-06 18:12:49,689 DEBUG Got 6.000 kB, SNR: 41.19 dB, drift: -0.01 ppm recv.py:151 2015-02-06 18:12:50,659 DEBUG Got 12.000 kB, SNR: 41.05 dB, drift: -0.00 ppm recv.py:151 2015-02-06 18:12:51,639 DEBUG Got 18.000 kB, SNR: 40.96 dB, drift: -0.00 ppm recv.py:151 2015-02-06 18:12:52,610 DEBUG Got 24.000 kB, SNR: 41.47 dB, drift: -0.01 ppm recv.py:151 2015-02-06 18:12:53,610 DEBUG Got 30.000 kB, SNR: 41.06 dB, drift: -0.00 ppm recv.py:151 2015-02-06 18:12:54,589 DEBUG Got 36.000 kB, SNR: 41.37 dB, drift: -0.00 ppm recv.py:151 2015-02-06 18:12:55,679 DEBUG Got 42.000 kB, SNR: 41.13 dB, drift: -0.00 ppm recv.py:151 2015-02-06 18:12:56,650 DEBUG Got 48.000 kB, SNR: 41.31 dB, drift: -0.00 ppm recv.py:151 2015-02-06 18:12:57,631 DEBUG Got 54.000 kB, SNR: 41.23 dB, drift: +0.00 ppm recv.py:151 2015-02-06 18:12:58,605 DEBUG Got 60.000 kB, SNR: 41.31 dB, drift: +0.00 ppm recv.py:151 2015-02-06 18:12:58,857 DEBUG EOF frame detected framing.py:57 2015-02-06 18:12:58,857 DEBUG Demodulated 61.205 kB @ 9.988 seconds (97.9% realtime) recv.py:176 2015-02-06 18:12:58,858 INFO Received 60.000 kB @ 9.988 seconds = 6.007 kB/s recv.py:180 2015-02-06 18:12:58,876 DEBUG Closing input and output amodem-cli:210 2015-02-06 18:12:58,951 DEBUG AsyncReader thread stopped (read 896000 bytes) async.py:28
After the receiver has finished, verify the received file’s hash:
~/receiver $ sha256sum data.rx 008df57d4f3ed6e7a25d25afd57d04fc73140e8df604685bd34fcab58f5ddc01 data.rx
You can see a video of the data transfer process.
Visualization
Make sure that matplotlib package is installed, and run (at the receiver side):
~/receiver $ amodem-cli recv --plot -o data.rx
Release history Release notifications | RSS feed
Download files
Download the file for your platform. If you're not sure which to choose, learn more about installing packages.
